Details

---

GL7000 specifications

Item		Description
Model number		GL7000
Number of module		Attached to up to 10 modules (*1)
Number of input channels		Max. 112 channels in 1 of GL7000
External Input/Output signals (*2)	Input	Start/Stop, External trigger, External sampling, Auto balance (*3) Signal type: Contact (relay), Open collector, Voltage
	Output	Trigger, Busy (*3), Alarm (10 channels) (*4) Signal type: Open collector (pulled-up by resistor 10 kΩ)
Trigger, Alarm function	Trigger action	Start or stop capturing data by the trigger
	Trigger repeat	Enabled (ON): Automatically re-armed for the next data capture function Disabled (OFF): Data capture is completed in a single trigger
	Trigger source	Start: Off, Measured signal, Alarm, External signal, Clock, Week or Time Stop: Off, Measured signal, Alarm, External signal, Clock, Week or Time
	Trigger determination conditions for measured signal	Combination: OR or AND condition at the level of signal or edge of signal Analog: Higher/Rising, Lower/Falling, Window-in, Window-out Logic (*5): Higher/Rising, Lower/Falling Pulse (*5): Higher/Rising, Lower/Falling, Window-in, Window-out
	Alarm determination condition (*6)	Combination: OR or AND condition at the level of signal or edge of signal Analog: Higher/Rising, Lower/Falling, Window-in, Window-out Logic (*5): Higher/Rising, Lower/Falling Pulse (*5): Higher/Rising, Lower/Falling, Window-in, Window-out
	Alarm output	10 channels
	Pre-trigger (*7)	Number of data before trigger: Up to specified number of captured data
Calculation function	Between channels	Addition, Subtraction, Multiplication and Division for two analog inputs (Sampling speed is limited up to 10 Samples/s (100 ms interval). Available arithmetic element and the output destination is the analog input channel 1 to 100.)
	Statistical	Select two calculations from Average, Peak, Max., Min. in real time and replay (*8)
Move function of the display range		Beginning, center or end of the data, Trigger point, Specific time (absolute, relative), Call cursor
Search function		Search for analog signal levels, logic signal pattern, pulse signal levels or alarm point in captured data
Annotation function		Comment can be set in each channel (up to 31 alphanumeric characters)
Message / Marker Functions		Message: The registered messages or entered message is able to be recorded for any timing. Up to 8 messages can be pre-registered. Marker: Marker is able to record for occurring alarm or power failure.
Resume		Resume automatically in the same condition after power is recovered as when the power failure occurred during data capture (*9)
FFT analysis function (Firmware ver. 1.20 or later)	Analyzing frequency range	0.08, 0.2, 0.4, 0.8, 1.6, 2, 3.2, 4, 8, 20, 40, 80, 200, 400, 800 Hz, 2, 4, 8, 20, 40, 80, 200, 400 kHz
	Number of points	500, 1000, 2000, 4000, 10000
	Window function	Rectangular, Hanning, Hamming, Blackman, Flat-top, Exponential
	Averaging	Summation average, Exponential average, Peak hold
	Channels	4 channels
	Functions	Y-T, Linear, Power, PSD, Cross, Transfer function, Coherence, COP
	Display mode	Single display, Dual display, Nyquist
Interface to PC		Ethernet (10 BASE-T/100 BASE-TX), USB 2.0 (High speed)
Network function		WEB server, FTP server, FTP client, NTP client, DHCP client
USB drive mode		Emulate the USB memory device (*10)
Storage device	Built-in	RAM (2 million samples, built-in amplifier module), Flash memory (2 GB, built-in the main module)
	External (*11)	SD card (Support SDHC, up to 32GB) slot, SSD (Approx. 64GB) The file for capturing data is limited up to 2GB.
Data saving function	Captured data (*11)	Built-in RAM, Built-in Flash, SD memory card, SSD (Data is saved directly to it.)
	Data in built-in RAM	Specified number of data up 2 million samples in increments of 1
	Auto save (*11)	Available for the built-in RAM Enabled (ON): Data in the RAM is saved automatically to the built-in Flash, SD memory card, SSD Disabled (OFF): Data in the RAM is not maintained after power is turned off
	Capturing mode (*11)	Mode: Off, Normal, Ring, Relay Ring (*12): Saved most recent data (Number of capturing data: 1000 to 2000000 points, Destination of data: Built-in RAM, Built-in Flash, SD memory card, SSD) Relay (*13): Saved data to multiple file without losing data until capturing data is stopped (Destination of data: Built-in Flash, SD memory card, SSD)
	During data capture (*15)	Displaying information in two windows, Hot-swapping the SD memory card, Saving data in between cursors.
	Backup (*11)	Backup interval: Off, 1, 2, 6, 12, 24 hrs. Data destination: SD memory card, SSD, FTP server Data destination for backup cannot be specified to the same storage for destination of capturing data.
Engineering Scale function		Measured value can be converted to the engineering unit Analog voltage: Converts by four reference points (gain, offset) Temperature: Converts by two reference points (offset) Pulse count: Converts by two reference points (gain)
Synchronization between units		Start and Trigger (*14)
Accuracy of clock (at 23°C)		±0.002% (Monthly deviation approx. 50 sec.)
Operating environment		0 to 45°C, 5 to 85% RH (non condensed)
Power source		100 to 240 V AC, 50 to 60Hz
Power consumption		85VA
Standard accessories		Quick guide, CD-ROM, AC power cable
External dimensions (W x D x H)		Main module: Approx. 193 x 141 x 160 mm (Excluding Projection), Alarm output terminal: Approx. 30 x 136 x 145 mm (Excluding projection)
Weight		Main module: Approx. 2.2 kg, Alarm output terminal: Approx. 350 g