Details
Available in 2 in. and 16 in. through 35 in. sizes, the low-cost HS-series pumps provide high speed, low ultimate pressure, high throughput, high tolerable forepressure, and low backstreaming. The HS-Series diffusion pumps come with full thermal protection and optional quick-cool coils. The 16 in. through 35 in. pumps come with sight glass/fill and drain assemblies, and are available with ASA or ISO flanges.
- Five-stage stainless steel fractionating jet purifies pumping fluid.
- Full thermal protection.
- Fluid-level sight glass provides quick indication of pump fluid level at all times.
- Fill and drain assembly for pump oil.
- Optional halo baffle cold cap reduces backstreaming without adding height.
- Standard gauge port (NW-25) below inlet flange included.
- Optional quick cool coil.
- Please note that this item is controlled for export by the Nuclear Suppliers Group. Accordingly, you may be required to obtain an export license from the U. S. Department of Commerce prior to exporting this pump from the United States. Please consult the U. S. Export Administration Regulations, ECCN 2B231, for further guidance.
Technical Specifications
|
Pumping Speed, Operating Range Pumping Speed, AVS 4.1 (1963) |
17,300 l/s Air, 21,625 l/s He and H2 32,000 l/s Air |
| Maximum Throughput | 30 T-l/s (40 mbar l/s) in operating range, 35 T-l/s (45 mbar-l/s) @ 0.01 torr |
| Operating Range | 1.7 x 10-3 to <5 x 10-8 torr (2.3 x 10-3 to <6.5 x 10-8 mbar) |
| Maximum Forepressure |
No Load: 0.50 torr (0.65 mbar) Full Load: 0.35 torr (0.45 mbar) |
| Recommended Backing Pump | ɛ300 cfm (510 m3/hr) |
| Backstreaming Rate, Standard Cold Cap | <7 x 10-4 mg/cm2/min |
| Warmup Time | 60 minutes |
| Cooldown Time | 180 minutes |
| Fluid Charge | 3 U.S. gallons (11.3 liters) |
| Electrical Requirements | 3 ph, 50/60 Hz, 240/415/480 VAC |
| Pump Power | 24,000 watts |
| Cooling Water Requirements | 4 gpm (800 l/hr) at 60-80°F (15-26°C) |
| Water Connections | 3⁄8 in. FPT Tee |
| Recommended Fluid | DC-704 |
Speed Curve Graph
Pumping Speed/Cold Cap Pumping speed/Halo Baffle Throughput
Outline Drawing
| Description | Voltage | Weight Kg (Lbs) | Part Number | |
| HS-32 Pump | Flange Type | |||
| Electrical Requirements | ASA | ISO | ||
| HS-32 with standard cold cap | 240 V | 612 (1,350) | 76134308 | L5923308 |
| HS-32 with halo baffle | 240 V | 612 (1,350) | 76134318 | L5923318 |
| HS-32 with standard cold cap | 415 V | 612 (1,350) | 76134326 | L5923326 |
| HS-32 with halo baffle | 415 V | 612 (1,350) | 76134336 | L5923336 |
| HS-32 with standard cold cap | 480 V | 612 (1,350) | 76134309 | L5923309 |
| HS-32 with halo baffle | 480 V | 612 (1,350) | 76134319 | L5923319 |
| Accessories | ||||
| Water-cooled halo baffle | 16 (35) | K1856332 | ||
| Centering ring for ISO foreline flange, 200K | 0.5 (1.0) | IC200SV | ||
| O-ring, ISO Inlet flange | 0.5 (1.0) | 78536002 | ||
| Instruction manual | 699901140 | |||
| Replacement Parts (six heaters required per pump) | ||||
| Heater*, 4000 W, 240 V/415 V/ 480 V with leads | 0.5 (1.0) | 647332010 | ||
|
Heater*, 4000 W, 240 V/415 V/ 480 V no leads used on pumps built before May 90 (*One heater consists of 2-120V heaters, right and left) |
0.5 (1.0) | 647332075 | ||
| Heater crush plate (replace one with each new heater) | 4.0 (8.0) | K7246001 | ||
| Heater insulator (one required per pump) | 0.5 (1.0) | 75792001 | ||
| Heater clamping plate (six required per pump) | K7247001 | |||
| Replacement o-ring kit for ASA pumps (kit contains: 1 inlet flange o-ring (buna 45390001), 1 foreline flange o-ring (butyl 2-443), sight glass o-ring and gasket, 8 fill and drain o-rings (Viton 2-213)) | 0.5 (1.0) | K0377167 | ||
| Sightglass service kit (pumps built before Oct. 95) | 1.5 (3.0) | F6097301 | ||
| ISO inlet flange o-ring | 78536002 | |||
| Upper (water) thermal switch (set at 550° F/288 °C) | 0.5 (1.0) | K9050005 | ||
| Lower (boiler) thermal switch (set at 220° F/104 °C) | 0.5 (1.0) | K9050004 | ||
| Cold cap gasket/grommet (kit of 4) | 0.5 (1.0) | L8839301 | ||
| Cold cap nut and follower (2 each) | 0.5 (1.0) | L8840301 | ||
| Heater Retrofit Kit (for pumps built before May 90; clamping plates not included) | ||||
| HS-32, 240 | 18.16 (40.0) | L6517308 | ||
| HS-32, 415 | 18.16 (40.0) | L6517326 | ||
| HS-32, 480 | 18.16 (40.0) | L6517309 | ||
View more about HS-32 on main site